Lighting - Lamps 

By on

edisonBulbPatent
Electric Lamp Patent by Edison, 1880
Image Source: ourdocuments.gov
Lamps are the essential part of any luminaire. These are the light generating components. Since the advent of electrical lighting in the middle of the 19th century, multiple types of lamps have been developed. Over the years lamp technology continues to evolve offering increases in performance and efficiencies.

Lamp Types

Filament Lamps

Electricity heats a filament until it is incandescent (around 2800 K).

  • General Lighting Service Lamp, GLS - designed for general lighting service with tungsten filament surrounded by inert gas and enclosed in a glass bulb.
  • Tungsten-halogen, TH - use of halogen vapour allows a higher operating temperature and increased efficacy

Discharge Lamps

Ionisation of a gas (or metallic vapour), initially by the application of an high voltage pulse followed by charged particles colliding with atoms. This causes radiation to be given off.

  • Low pressure lamps - have relatively long distances between collisions allow charged particles to build up sufficient speed to cause excitation
  • High pressure lamps - an increase in the number of collisions (due to a denser arrangement of atoms) causes sufficient heat to raise the temperature of the gas
  • Fluorescence - low pressure mercury discharge produces ultra-violet radiation, converted to visible light by fluorescent or phosphor coating

Sarters (Ballasts)
Discharge lamps require starters to enable a high voltage to be applied to the lamp during starting , while limiting the current flowing once the gas has become ionised.  Possible starters include:

  • Resistance - can limit current flowing, not used due to large heat dissipation
  • Reactance - can limit current flowing, commonly used
  • Capacitance - can limit current flowing, only used on rare occasions
  • Ignitor - generates series of high voltage pulses,  staring of lamps at voltages higher than mains
  • Reactance autotransformer - provides higher than mains stating voltage, limits operation current
  • Glow starter - closes or opens the pre-heating circuit of a fluorescent tube
  • Electronic starter - device for fluorescent tubes to provide necessary pre-heating of the electrodes

Modern Technology

Recent drives to create more efficient and environmentally friendly lamp technology has see much research and development in the fields of LED and Induction Lamps.

  • LED (Light Emitting Diode) - electric current flowing through a semi-conductor junction cause light to be emitted.
  • Induction Lamp a high frequency electromagnetic field is injected is used to excite mercury, producing UV radiation and phosphor coating converts to visible light

Summary of Lamp Characteristics



Lamp


Description

Watts
W

Efficacy
lm W-1
Life (hours) 
1000's
Colour
Typical
Application
CCT RG Class
Filament
GLS

General lighting service

25 to 1000

8 to 18

1 to 2

2800

1A Warm Home

TH

Tungsten halogen

25 to 1500

18 to 24

2 to 4

2900 1A Warm Display
Tubular Fluorescent

T5

15 mm diameter 4 to 80 37 to 94 1 to 4 2800 to 6500 1A,1B,2,3 All

Factory, office & shops

T8 26 mm diameter 18 to 70 75 to 93 1 to 1.5 As above As above All  
T12 38 mm diameter       As above As above All  
Sodium

SOX

Low pressure

10 to 135

100 to 200

6 to 20

None     Roads

SON

High pressure

50 to 1000

70 to 130

6 to 24

2000 to 2200 2,4 Warm Industry
Mercury
MBF High pressure

50 to 1500

35 to 55

5 to 24

3800 3 Intermediate Industry
MBTF High pressure blended (MBF+filament)

50 to 1500

           
Metal halide
MBI High pressure discharge

70 to 1000

65 to 85

5 to 12

5200 2 Intermediate Industry, commerce

If your looking for a good (more detailed) comparison of technical parameters across all lamps, the Thorn Technical Handbook is a good resource (freely available online)

Typical Currents & Recommended Fuse/MCB Ratings

  Current (A) Fuse/MCB (A) for No.Lamps
Watt μF Start Run 1 2 3 4 5 6

SOX

18

     

4

4

4

4

4

4

SOX

35

     

4

4

4

4

4

4

SOX

55

     

4

4

4

4

4

4

SOX

90

     

4

4

4

4

6

6

SOX

135

     

4

10

10

16

20

25

SON

50

 

0.35

0.3

4

4

4

4

4

4

SON

70

 

0.55

0.4

4

4

4

6

6

10

SON

100

 

0.7

0.52

4

4

4

6

10

10

SON

150

 

0.7

0.8

4

6

10

10

16

16

SON

250

 

1.5

1.3

10

16

16

20

20

20

SON

400

 

3.0

2.15

16

20

20

25

25

32

SON

1000

 

6.0

5.4

20

25

32

40

50

63

MBF

50

6

0.32

0.3

4

4

4

4

4

4

MBF

80

8

0.5

0.4

4

4

4

4

6

6

MBF

125

8

1.1

0.7

4

4

6

10

10

10

MBF

250

13

2.2

1.33

10

16

16

20

20

20

MBF

400

20

4.0

2.2

16

20

20

25

25

25

MBF

700

20

6.5

3.5

16

20

25

32

32

40

MBF

1000

50

9.0

5.5

20

25

32

40

50

63

MBI

150

20

0.76

0.76

4

6

10

10

16

16

MBI

250

30

1.5

1.3

10

16

16

20

20

20

MBI

400

25

3.5

2.0

16

20

20

25

25

25



Steven McFadyen's avatar Steven McFadyen

Steven has over twenty five years experience working on some of the largest construction projects. He has a deep technical understanding of electrical engineering and is keen to share this knowledge. About the author

myElectrical Engineering

comments powered by Disqus



Understanding Circuit Breaker Markings

IEC 60947 is the circuit breaker standard and covers the marking of breakers in detail. Any manufacturer following this standard should comply with the...

Resistors

Resistors are electronic components that oppose the flow of current.  Manufactured in various types and ranges they have a wide application to electronics...

Smarter Electrical Distribution

The other day I came across an article in Technology Review on the development of a smart transformer. A professor at North Carolina State University is...

Lightning Risk Assessment (IEC 62305)

IEC 62305 'Protection against lightning' requires a risk assessment be carried out to determine the characteristics of any lightning protection system...

Lightning Protection and Earth Electrode Resistance

Most installations involve some form of lightning protection system which is connected to an earth electrode.  The function of the earth electrode is to...

Understanding electric motor insulation & temperature

Anyone specifying or using electric motors should have a basic understanding how the insulation is related to temperature. Three classes of insulation...

MIT OpenCourseWare

MIT OpenCourseWare, makes the materials used in teaching all MIT subjects available on the Web, free of charge, to any user in the world.

Why use catalogues

I'm a fan of using manufacturers catalogues. There are two main reasons for this. Firstly, if your involved in the purchase of equipment, you will likely...

Always Use PPE

A lot of our members work in countries where PPE (personal protective equipment) is regulated or they work for companies/organizations which take employee...

Power Transformers - An Introduction

One of the fundamental requirements of an alternating current distribution systems it to have the ability to change the magnitude of voltages.  It is more...

Have some knowledge to share

If you have some expert knowledge or experience, why not consider sharing this with our community.  

By writing an electrical note, you will be educating our users and at the same time promoting your expertise within the engineering community.

To get started and understand our policy, you can read our How to Write an Electrical Note