Notes

ABB Technical Guides - Motor Operation 

By on

ABB Motor Technical GuideABB has produced a range of technical guides that offer concise explanations of the major technologies and technical issues in low voltage AC drives.  The technical guides cover subjects such as the basics of variable-speed drives, dimensioning a drive system, electrical braking, harmonics and AC drives, and bearing currents.

 Currently the ABB site lists the following guides:

  • Application Guide, Guide to extruders in AC drives
  • Sustainability guide, Driving energy efficiency worldwide, ABB motors and drives
  • Technical Guide, Direct Torque Control
  • Technical guide, Functional safety
  • Application guide, ABB drives, Using variable speed drives (VSDs) in pump applications
  • Technical Guide, EU Council Directives and Adjustable Speed Electrical Power Drive Systems
  • Technical guide, EMC compliant installation and configuration for a power drive system
  • Technical Guide, Guide to Variable Speed Drive
  • Technical Guide, Bearing Currents in Modern AC Drive Systems
  • Technical Guide, Guide to Harmonics with AC Drives
  • Technical Guide, Dimensioning of a Drive system
  • Technical Guide, Electrical Braking
  • Technical guide, Guide to motion control drives

The guides can be accessed at:

ABB Technical Guides - Motor Operation

, ,

More interesting Notes:
Steven McFadyen's avatar Steven McFadyen

Steven has over twenty five years experience working on some of the largest construction projects. He has a deep technical understanding of electrical engineering and is keen to share this knowledge. About the author

myElectrical Engineering

comments powered by Disqus

View 2 Comments (old system)

  1. beho2000's avatar beho2000 says:
    9/1/2011 2:11 PM

    Thanks alot for this guide Could you pleas help me to find ( Worked Example on DOCWIN) best wishes

    • Steven's avatar Steven says:
      9/1/2011 2:11 PM

      I have not used DOCWIN. We mainly AMTECH here. If you Google you may be able to find something, otherwise I would just play around with the software. You could also try starting a forum post and see if anyone else has examples.

Comments are closed for this post:
  • have a question or need help, please use our Questions Section
  • spotted an error or have additional info that you think should be in this post, feel free to Contact Us
Differential protection, the good old days

This morning I was explaining how differential protection works to a junior engineer. To give him something to read I opened up the NPAG (Network Protection...

E-Ink

Before the technical, some general information. E-ink display are found in a lot of e-readers, some mobile phones and similar devices and the intent is...

What is an Open Delta Transformer

In three phase systems, the use of transformers with three windings (or legs) per side is common.  These three windings are often connected in delta or...

Post Authorship

In 2011, with the introduction of it’s Panda search ranking algorithms, Google introduced tools for determining the original author of posts.  The intention...

Difference Between Live and Dead Tank Circuit Breakers

A quick post in connection with an email question: Live Tank - the circuit breaker the switching unit is located in an insulator bushing which is live...

Hazardous Areas – IEC and NEC/CEC Comparison

Depending where in the world you work, you are likely following one of two standards International Electrotechnical Commission (IEC) National...

Fault Calculations - Typical Equipment Parameters

A frequent problem in fault calculations is the obtaining of equipment parameters.  While it is always preferable to use the actual parameters of the equipment...

Introduction to Cathodic Protection

If two dissimilar metals are touching and an external conducting path exists, corrosion of one the metals can take place.  Moisture or other materials...

International System of Units (SI System)

The International System of Units (abbreviated SI) is the world's most widely used system of units.  The system consists of a set of units and prefixes...

What does N+1 mean?

The term 'N+1' relates to redundancy and simply means that if you required 'N' items of equipment for something to work, you would have one additional...

Have some knowledge to share

If you have some expert knowledge or experience, why not consider sharing this with our community.  

By writing an electrical note, you will be educating our users and at the same time promoting your expertise within the engineering community.

To get started and understand our policy, you can read our How to Write an Electrical Note. 

Footer
(click here to extend)
Copyright (c) 2026 myElectrical